It appears that your cart is currently empty
Specification: ( Manual)
| Product Name | SpeedyBee F7 V3 Flight Controller |
| MCU | STM32F722 |
| IMU(Gyro) | BMI270 |
| USB Port Type | Type-C |
| Barometer | BMP280 |
| OSD Chip | AT7456E chip |
| BLE Bluetooth | Supported. Used for Flight Controller configuration,built-in a single 2.4 GHz Wi-Fi-and-Bluetooth combo chip |
| Flash FC Firmware Wirelessly | Supported. Please enter MENU > FC Firmware Flasher |
| Download/Analyze Blackbox | Supported.Please enter MENU > Blackbox Analyzer |
| DJI Air Unit Connection Way | Two ways supported: 6-pin connector or direct soldering. |
| 6-pin DJI Air Unit Plug | Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed. |
| Flash(for BlackBox) | 500MB |
| BetaFlight Camera Control Pad | Yes(CC pad on the front side) |
| Power Input | 3S - 6S Lipo |
| 5V Output | 10 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 6 +5V output included in the connectors on bottom side. The total current load is 2A. |
| 9V Output | 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 4A. |
| 3.3V Output | Supported. Designed for 3.3V-input receivers. Up to 500mA current load. |
| 4.5V Output | Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load. |
| ESC Signal Pads | M1 - M4 on bottom side and M5-M8 on front side. |
| UART | 5 sets(UART1, UART2, UART3, UART4(For ESC Telemetry), UART6) |
| ESC Telemetry UART | R4(UART4) |
| I2C | Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc. |
| LED Pad | Used for WS2812 LED controlled by Betaflight firmware. |
| Buzzer | BZ+ and BZ- pad used for 5V Buzzer |
| BOOT Button |
Supported. [A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked. [B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware. |
| RSSI Input | Supported. Named as RS on the front side. |
| SmartPort | Supported |
| Supported Flight Controller Firmware | BetaFlight(Default),INAV |
| Firmware Target Name | SPEEDYBEEF7V3 |
| Mounting | 30.5 x 30.5mm( 4mm hole diameter) |
| Dimension | 41(L) x 38(W) x 8.1(H)mm |
| Weight | 10.7g |
| Product Name | SpeedyBee BL32 50A 4-in-1 ESC |
| Firmware | SpeedyBee BL32 50A |
| Configurator Download Link | http://github.com/bitdump/BLHeli/releases |
| Continuous Current | 50A * 4 |
| Burst Current | 55A(5seconds) |
| TVS Protective diode | Yes |
| Heat Sink | Yes |
| External Capacitor | 1000uF Low ESR Capacitor(In the package) |
| ESC Protocol | DSHOT300/600 |
| PWM Frequency Range | 16KHz-128KHz |
| Power Input | 3-6S LiPo |
| Power Output | VBAT |
| Current Sensor | Support (Scale=490 Offset=0) |
| ESC Telemetry | supported |
| Mounting | 30.5 x 30.5mm( 4mm hole diameter) |
| Dimension | 45.6(L) * 40(W) * 8.8mm(H) |
| Weight | 19.2g with heat sink |
Package Included:
SpeedyBee F7 V3 Flight Controller × 1
SpeedyBee BL32 50A 4-in-1 ESC × 1
DJl 6pin Cable(80mm) × 1
SH 1.0mm 25mm-length 8pin Cable(for FC-ESC connection) × 1 M3*8mm Silicone Grommets(for FC)× 1
M3*8.1mm Silicone Grommets(for ESC) × 1
M3*30mm Iner-hexagon Screws × 5
M3 silicone O Ring × 5
M3 Nylon Nut × 5
35V 1000uF Low ESR Capacitor × 1
XT60 Power Cable(70mm) × 1
4pin SH1.0 to 3+2pin JST1.25 FPV Cam Cable(30mm) × 1
4pin SH1.0 to 3+2pin JST1.25 FPV Cam Cable(60mm) × 1
4pin SH1.0 to 4pin JST1.25 FPV Cam Cable(60mm) × 1
4pin SH1.0 Radio Receiver Cable(100mm) × 1
4pin SH1.0 to 4pin SH1.0 Analog VTX Cable × 1
6pin SH1.0 GPS Module Cable without Connector on another end(100mm) × 1
6pin SH1.0 GPS Module Cable Connector of another end × 1
Related product
HappyFish.co.za
M5 Airdrop Air Dropping System R...
M5 Airdrop Air Dropping System Remote Thrower Transp...
R 600.00 R 499.99
M5 Airdrop Air Dropping System Remote Thrower Transport Gift Delivery Device for RC Drone QuadcopterDescription:Item Type: Air-Dropping Material: ABSColor: BlackMaximum load: 75...
HF-A-D
30cm Wooden Nutcracker Doll Sold...
This little soldier is more than just a decoration f...
R 710.00 R 585.78
This little soldier is more than just a decoration for your home. He's a symbol of strength and courage that will protect your family from evil. He's also said to bring good luc...
HappyFish.co.za
2PCS Upgraded Metal Front Rear B...
Description:Item Name:Front rear bridge axleMaterial...
R 1,040.00 R 859.99
Description:Item Name:Front rear bridge axleMaterial:Zinc alloy pressure casting paintColor:Red,black and silverProduct Size:Front axle width is about 141mm,rear axle width is a...
HappyFish.co.za
2PCS Upgraded Metal Front Rear D...
Description:Item Name:Front rear drive shaftMaterial...
R 405.00 – R 425.00
Description:Item Name:Front rear drive shaftMaterial:SteelColor:Black and silverProduct Size:About 69.5mm-94mm,hole diameter is 4mmProduct Weight:About 38gCompatible Model:MNRC ...
HappyFish.co.za
687pcs Wall-E Robot 18cm Blocks ...
Specifications:Product Code: NO.8886Color: YellowPro...
R 1,150.00 R 879.99
Specifications:Product Code: NO.8886Color: YellowProduct Dimensions: 16*16*18cmPiece Count: 687pcsMaterial: ABSFeatures:Experience WALL-E like Never Before: Enter the world of y...
HappyFish.co.za
F701 2.4GHz 7CH Ultra Long Range...
F701 2.4GHz 7CH Ultra Long Range PPM DSMX/DSM2 RC Re...
R 620.00 R 470.00
F701 2.4GHz 7CH Ultra Long Range PPM DSMX/DSM2 RC Receiver for JR Spektrum DX6I DX7 DX9 TransmitterThe FSFLY Series receiver uses DSSS-2 and DSSS-X technology, compatible with S...