It appears that your cart is currently empty
Introduction:
This is a mini gasoline engine model that is designed with the same structure as the real diesel enginethe only difference is that it is a gasoline engine.
Each part has been designed and processed by our energy . It is processed by brass and stainlesssteel . It uses a water cooling heat structure.
The capacity of the water tank reaches the amazing 30ml . There is a float and benchmark in the watertank . It can show the liquid level of water！
Double flywheel design reduces the low speed response of ancient engine , and the flying wheel onboth sides of the engine is mounted with different sizes of pulley .
It installs a tape oil for adjustable speed . It sets a throttle switch that can link to control the speed of theengine . The igniter is powered 4 . 5V .
It uses gasoline as a fuel , when you launch it . It will become a violent small machine !Starting method : external force ( high speed drill )
Specification:
Name: Mini M26 Gasoline Engine Model
Size : 115 * 90 * 80MM
Displacement : 1 . 9CC .
Cylinder diameter : 13MM .
Itinerary : 14MM
Weight : 1300G
Features:
Engine startup steps:
1.Check the wiring of the engine from the board , connect the fuel tank pipeline , and install 3 No 5battery ( 4 . 5v )
2 . Use gasoline ( 95 # ) to fill the fuel tank . After the filling is completed , turn the flywheel clockwise onthe right side of the engiswitch surface ) for many turns . No air can be generated.
3 . Turn on the power switch and quickly rotate the flywheel clockwise on the right side of the engine( power switch surface ) to start the engine.
Precautions
1.If the ignition device is normal and the cylinder compression is normal , if the machine cannot startnormally , it is very likely that the carburetor oil needle needs to be adjusted.
2 . After tightening the main oil needle on the carburetor , loosen 1 / 4 turn and start the flywheel , so thatthe mixing ratio of gasoline and air can reach the normal working mixing ratio.
3.When the machine stops , the power switch should be turned off .
1 . Product maintenance method
The engine is water-cooled , and you need to add water before each work . When you finish the work ,ou need to save the water .
The working environment should be ensured in a clean environment to reduce the possibility of dustentering the carburetor .
The carburetor oil needle has been adjusted in the best position before shipment . It is notrecommended to make a large adjustment . But it can be fine-tuned under different fuels.
The cylinder head cover can be disassembled and lubricated on the valve mechanism.
After the engine stops working , you need to remove the battery and save it.
2 . Troubleshooting method
The engine needs a new battery to make sure it has enough voltage for the igniter to work properly.
When adding fuel from the fuel tank . But there will be air in the fuel tank . You need to hold thecarburetor port by hand . Rotate the flywheel . The piston allows the engine to suck fuel into the carburetor.
The engine has been adjusted for work ( using gasoline ) before shipment , but the setting of thecarburetor may need to be fine-tuned under different fuels . You can fine-tune the size of the main oil needle.
3 . Lubrication methods and methods can add no more than 4ML of lubricating oil to the crankcase toensure splash lubrication of the crankshaft.
4 . What kind of fuel and amount to use The oil tank capacity is about 15ML . The engine can usegasoline and aviation kerosene . The engine needs to add 4% lubricating oil to the fuel.
If there is no compression , there should be a foreign body entering the engine , which prevents the valve from closing normally.There are three ways to try to solve it.
1. Put a few drops lubricating oil on the carburetor . Use an eletric dril to drive the engine for awhile Under the action of the lubricating oil , the foreign matter is discharged to restore the cylinder pressure.
2.Use an electric drill to rotate the hour hand ( the opposite direction of the engines working direction )to rotate the engine for a while . Discharge the foreign matter by turning the rotation.
3.Remove the cylinder head.Foreign matter on the valve may cause the valve to not close properly. Check the foreign matter on the valve and restore the cylinder pressure after cleaning.
4.The valve timing gear may be caused by disorder .
Note:
1. Please understand the product might have some colour difference due to different monitors and scenes.
2. Please allow slight deviation for the measurement data.
Package Included:
1x Mini M26 Gasoline Engine Model
